WAZIPOINT Engineering Science & Technology: Why Need Power Cable Test After Installation

Tuesday, June 1, 2021

Why Need Power Cable Test After Installation

Electrical Power Cable Test Procedure in Field After Installation

Power Cable Test After Installation

HV/EHV power cable testing at the field after installation is the common requirements of cable user. While MV-normal voltage, HV-high voltage and EHV-extra high voltage power cables are carefully tested by the manufacturer before consignment with AC-alternating or DC-direct voltage. 

Some defects may not be detected or, more likely, damage may occur during shipment handling, carrying to storage and site, or during installation. To make over-sure additional testing carry out after installation and prior to being placed in service, including joints and terminations, may be conducted. 

Moreover, many users find that gradually cable systems degrade and service failures which become troublesome for them. Due to that, they desire to reduce or eliminate those failures by performing periodic tests after some time in service. Determining the economic replacement of the downgraded cable, users need a special diagnostic test.

Power cable test in field after installation may be broadly divided into the following two categories:

A.   Field tests are intended to detect defects in the insulation of a cable system in order to improve the service reliability after the defective part is removed and appropriate repairs performed. These tests are usually achieved by application of relatively elevated voltages across the insulation for prescribed duration.


B.   Field tests are intended to provide indications that the insulation system has deteriorated. Some of these tests will show the overall condition of a cable system and others will indicate the locations of discrete defects which may cause the sites of future service failures.  Both varieties of such tests may be categorized as “pass/fail” or “go/no-go” and are usually performed by means of moderately elevated voltages applied for a relatively short duration, or by means of low voltages.

Applied Voltage Type for Cable Test:

Sponsored:

Both of Direct Current Voltage and Alternating Current Voltage has been accepted for many years as the standard method.


DC test for Power Cable: 

DC testing method is performing for a long time as high voltage tests on cable insulation systems, especially for a field test. But recent research has shown that dc testing is the causes of certain types of defects and that it can make worse the deteriorated condition of some aged cables insulated with extruded dielectrics and affected with water trees.

AC test for Power Cable: 

Alternating voltage tests at alternating voltages are highly acceptable since the insulation is stressed in a similar way to normal operation and the test is similar to that used in the factory on new reels of cable. But high voltage AC tests equipment normally heavy, bulky and expensive test transformers which may not be readily transportable to a field site.

During high voltage test carry out of power cable in site after installation the grounding system should be sufficiently, due to long periods of time following such tests can experience dangerous charge build-ups and cause an accident. To avoid any mistake recommended grounding procedure and appropriate working rules should be followed.

Sponsored:



13 comments:

  1. Thank you so much for sharing this great blog, its been a really very helpful read! I am very thankful to the you for giving this interesting post.

    ReplyDelete
    Replies
    1. Thank you very much for your valuable comments;

      Delete
  2. Very nice description and layout of this product. I can think of quite a few of your tasty creations you can “save” for when I visit.

    ReplyDelete
  3. Thanks for sharing us this valuable blog.

    ReplyDelete
  4. I really enjoyed reading this post, big fan. Keep up the good work and please tell me when can you publish more articles or where can I read more on the subject?

    Underground Cable

    ReplyDelete
  5. Great post I would like to thank you for the efforts you have made in writing this interesting and knowledgeable article.
    Underground Cable

    ReplyDelete
  6. Great Article! I got too much information regards HVAC Services and I will follow this tips. Thanks for sharing such a helpful article. Click here to more information about it

    ReplyDelete
  7. Thank you for sharing the valuable content.

    The electrical test and measurement range of products from Josts’ Electrical Division ensures performance and reliability in power generation, transmission and distribution equipments. Josts has rich experience of over eight decades in providing advanced technology products and systems dedicated to various applications in Electrical Industry. Josts has pioneered many concepts in electrical testing and measurement for various applications in India such as Insulation Testing,

    electrical testing and measurement
    Climatic Test Chambers

    ReplyDelete
  8. I am looking for test tag sydney and your post is very good written that I have find here. It is very nice post. Thanks for sharing. Keep it up.

    ReplyDelete
  9. Thanks for sharing this information. I really like your blog post very much. You have really shared a informative and interesting blog post with people.. Gossip

    ReplyDelete
  10. I recently hired a Network Cabling Installer for my office, and I'm impressed with the professionalism and efficiency they brought to the table. Their expertise in network cabling services ensured that our network installation was smooth and hassle-free. I highly recommend their cabling solutions to anyone in need. #networkcablinginstaller #networking #installations

    ReplyDelete

WAZIPOINT:
Thank you very much to visit and valuable comments on this blog post. Keep in touch for next and new article. Share your friends and well-wisher, share your idea to worldwide.

You may like the following pages